Just about every person maintains their personal opinion when it comes to Tools You Need to Install a New Bathtub .
Installing a bathtub isn't exactly brain surgery, but it does require solid plumbing, carpentry, and in some cases, tiling skills. Changing an old bath tub with a new one is also a moderately difficult job. If the old tub is easily obtainable, the project can move immediately; if you need to open up a wall surface to remove the old bathtub and position the new bath tub, the job is a lot harder. In either case, the project is within a house handyman's abilities, although you will certainly require a helper to move out the old tub and set in the new one. Make sure you have certified on your own for the work and also fit trying it. As opposed to working with a specialist to take control of a halfway-completed job, it is much better to think about employing one before you begin. Chances are you might require a specialist plumber to make tube links.
This post will help you mount a brand-new tub in your restroom if you have already acquired a brand-new bathtub as well as don't need to transform the setup of your previous water pipelines.
Your tools and also product list must comprise the following:
Planning for the Installment
First of all, the supporting frame provided with the bath should be fitted (if called for) according to the maker's directions. Next off, fit the taps or mixer to the bathtub. When suitable the faucet block, it is essential to see to it that if the tap comes with a plastic washing machine, it is fitted between the bath and also the taps. On a plastic bath, it is additionally practical to fit a supporting plate under the faucets unit to stop stress on the bathtub.
Fit the adaptable tap connectors to the bottom of both taps making use of 2 nuts and olives (occasionally supplied with the bathtub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink outlet opening, and after that pass the electrical outlet through the hole in the bathroom. Make use of the nut supplied by the supplier to fit the plug-hole. Check out the plug-hole outlet for an inlet on the side for the overflow pipeline.
Next, fit completion of the adaptable overflow pipe to the overflow electrical outlet. After that, screw the pipe to the overflow face which need to be fitted inside the bath. Make certain you use all of the supplied washing machines.
Attach the trap to the bottom of the waste electrical outlet on the bath tub by winding the thread of the waste electrical outlet with silicone mastic or PTFE tape, and also screw on the trap to the electrical outlet. Attach the bottom of the overflow tube in a comparable manner.The bathroom must now be ready to be suited its final placement.
Removing Old Taps
If you require to change old taps with brand-new ones as a part of your installation, after that the first thing you need to do is separate the supply of water. After doing so, switch on the taps to drain any kind of water remaining in the system. The procedure of getting rid of the existing taps can be rather bothersome because of the limited gain access to that is often the situation.
Make use of a basin wrench (crowsfoot spanner) or a tap device to reverse the nut that connects the supply pipes to the faucets. Have a cloth prepared for the continuing to be water that will certainly come from the pipelines. As soon as the supply pipes have been eliminated, make use of the same tool to loosen up the nut that holds the faucets onto the bath/basin. You will need to quit the single taps from transforming throughout this process. Once the taps have actually been gotten rid of, the holes in the bath/basin will have to be cleaned up of any kind of old securing compound.
Prior to moving on to fit the new taps, compare the pipeline links on the old faucets to the brand-new taps. If the old taps are longer than the brand-new taps, then a shank adapter is required for the brand-new faucets to fit.
Mounting the Bathtub
Using the two wooden boards under its feet, put the tub in the called for placement. The wood boards are helpful in evenly spreading the weight of the bathtub over the area of the boards rather than focusing all the weight onto 4 little factors.
The following objective is to make certain that the bath tub is leveled all round. This can be attained by examining the level and adjusting the feet on the bathtub until the spirit level reads level.
To install taps, fit the bottom of the furthest flexible tap adapter to the appropriate supply pipeline by making a compression sign up with; after that do the very same for the various other faucet.
Turn on the water system as well as inspect all joints as well as new pipework for leaks and tighten them if necessary. Fill the tub as well as likewise inspect the overflow outlet and the normal electrical outlet for leakages.
Ultimately, take care of the bathroom paneling as explained in the producer's instruction manual. Tiling and securing around the bath tub must wait up until the tub has been used at the very least when as this will settle it right into its final position.
Suitable New Taps
If the tails of the new faucets are plastic, then you will require a plastic port to prevent damages to the thread. One end of the adapter fits on the plastic tail of the faucet and the other end provides a link to the existing supply pipelines.
If you require to fit a monobloc, then you will certainly require lowering couplers, which links the 10mm pipeline of the monobloc to the common 15mm supply pipe.
Next off, position the faucet in the mounting opening in the bath/basin ensuring that the washers remain in place in between the tap as well as the sink. Safeguard the tap in position with the manufacturer supplied backnut. As soon as the tap is firmly in place, the supply pipes can be attached to the tails of the taps. The faucets can either be attached by using corrugated copper piping or with typical faucet connectors. The previous kind ought to be attached to the tap ends initially, tightening only by hand. The supply pipelines can later on be connected to the various other end. Tighten up both ends with a spanner after both ends have been linked.
Tiling Around the Bath tub
In the area where the bath satisfies the floor tile, it is necessary to seal the accompanies a silicone rubber caulking. This is important as the fitting can relocate sufficient to crack a stiff seal, creating the water to pass through the wall between the bathroom and also the tiling, leading to problems with moisture and also feasible leaks to the ceiling below.
You can select from a selection of coloured sealers to blend in your fixtures as well as installations. They are marketed in tubes and also cartridges, and are capable of sealing spaces as much as a size of 3mm (1/8 inch). If you have a bigger void to fill, you can fill it with twists of soaked newspaper or soft rope. Keep in mind to constantly load the bath tub with water before sealing, to allow for the movement experienced when the tub is in usage. The sealer can split rather very early if you do not take into account this activity before sealing.
Alternatively, ceramic coving or quadrant tiles can be used to edge the bath or shower tray. Plastic strips of coving, which are easy to use and cut to size, are also easily available on the marketplace. It is suggested to fit the floor tiles making use of waterproof or water-proof glue and also cement.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
I stumbled upon that content on How to Install a Bathtub when surfing around the web. Sharing is nice. You never know, you may very well be helping someone out. Thanks for going through it.
More Details